Product introductionThe automobile suspension device inspection table (hereinafter referred to as the suspension table) can carry out the following tests on automobile suspension devices with axle weight less than 3 t:
Product introduction
The automobile suspension device inspection table (hereinafter referred to as the suspension table) can carry out the following tests on automobile suspension devices with axle weight less than 3 t:
1, vehicle static wheel mass 2, vehicle dynamic wheel mass 3, absorption rate 4, vibration waveform
Research and development basis
1, JT/T448-2001 "Automobile Suspension Device Testing Platform"
2. JJF 1192-2008 Calibration Specification for Test Bench of Automobile Suspension Device
Technical characteristics
The suspension platform is designed, manufactured and tested according to JT/T 448-2001 "Automobile Suspension Device Testing Platform".
The product meets the national standard GB 18565-2016 "Comprehensive Performance Requirements and Inspection Methods for Road Transport Vehicles".
Adopt new spraying technology, corrosion resistance and beautiful shape.
The frame is an integral box structure with high strength and small height.
The bearing bedplate on each side adopts the structure of 4 sensors and 4 eccentric wheels, which has strong overload capacity. The suspension platform can carry a car with an axle load of 13t without passing through the car board.
Landing instrument test system, the system has overload protection function.
Fast detection speed, high precision of test data and good repeatability.
The product is calibrated according to JJF 1192-2008 "Calibration Specification for Test Bench of Automobile Suspension Device".
The system has an open interface design, which is suitable for accessing various types of vehicle detection networks.
technical parameter
| Maximum through axle load | 3t /10 t |
| Rated bearing mass | 3T |
| Repeatability of absorption efficiency，% | 2 |
| Deck span | 700mm~2100mm |
| Vibrating plate size (mm) | 320mm×710 |
| Test track | 1000mm~1900mm |
| Table amplitude | 6mm |
| Excitation frequency | ＞15HZ |
| Excitation motor power | 1.5KW×2 |
| Rated speed of excitation motor | 1450r/min |
| Overall dimension (L×W×H), mm | 2520×650×230 |
| Power Supply | 380V±10%，50Hz±2% |
| noise | ＜75dB |
Leave your contact information, and our engineers will help you find the solution you are looking for.
Motorcycle safety performance testing equipment is used to test motorcycle wheel (axle) weight, speedometer accuracy, braking performance and wheel deflection. Friction inspection equipment is suitable for two-wheeled, three-wheeled and three-wheeled motorcycles that meet the following table.
KNOW MORE
Handheld terminal installed with relevant mobile application software, which is specially used for motor vehicle inspection or motor vehicle safety technical inspection.
KNOW MORE
Product introductionWGDP-10/13/15 automobile suspension steering system clearance tester (hereinafter referred to as product) is used to check the clearance between automobile suspension system and steering system matching parts. This product is suitable
KNOW MORE
Functional useThrough the intelligent measuring device, the three-dimensional image of the vehicle profile and the comprehensive monitoring data of length, width, height, container rail height, wheelbase and pin wheelbase are obtained. For the semi-trailer type, the tractor and the trailer can pass through the system together, and the relevant information of the tractor and the trailer can be measured
KNOW MORE
Product introductionThe automobile suspension device inspection table (hereinafter referred to as the suspension table) can carry out the following tests on automobile suspension devices with axle weight less than 3 t:
KNOW MORE Automobile 4-in-1 testing equipment is specially designed to meet the requirements of automobile 4S stations, maintenance service centers, small automobile testing stations, bus passenger stations, teaching and scientific research units, etc. It occupies less land, has high testing accuracy and simple operation, and is widely used in automobile repair shops, 4S shops, etc.
KNOW MORE
Automobile three-in-one testing equipment is specially designed to meet the requirements of automobile safety performance index testing in automobile 4S stations, maintenance service centers, small automobile testing stations, bus passenger stations, teaching and scientific research units, etc. It occupies less land, has high testing accuracy and simple operation, and is widely used in automobile repair shops and 4S shops.
KNOW MORE
Product introductionThis wheel gravimeter is used to measure the wheel mass, axle load mass and vehicle mass. Can be used independently, and can also be used for on-line use of automobile detection lines. LZ-3B/10B/13B wheel weight tester is suitable for two-axle vehicles with wheel weights
KNOW MORE
This test bench is mainly used to dynamically measure the front wheel side slip of an automobile and judge whether it is abnormal. WGCH-3F/10F/13F/13FS is suitable for all types of automobiles with axle load mass not more than 3000/10000/10000/13000/13000kg.
KNOW MORE
The automobile flat-panel testing platform is suitable for testing vehicles with the maximum dynamic weight of a single axle not exceeding 10000kg. On the flat-panel simulating the actual flat road, the automobile runs at a certain speed, implements braking, and dynamically measures the braking force, axle load
KNOW MORE
ZD-3BW/10BW, ZD-10DW/13DW, ZD-18BW, ZD-18DW series automobile loading and braking test stands are mainly used for testing automobile braking performance under rated load quality, and can detect the braking force sum and braking force difference (maximum process difference) of each axle of the automobile;
KNOW MORE
Drum-type automobile speedometer inspection platform (hereinafter referred to as speedometer). It is mainly used to test the accuracy of automobile speedometer. Model SD-3/10A/13A and B speedometer are suitable for all types of cars with axle loads not more than 3 000, 10 000 and 13 000㎏.
KNOW MORE
ZD-3BW/10BW, ZD-10DW/13DW, ZD-18BW, ZD-18DW series automobile loading and braking test stands are mainly used for testing automobile braking performance under rated load quality, and can detect the braking force sum and braking force difference (maximum process difference) of each axle of the automobile;
KNOW MORE
Drum-type automobile speedometer inspection platform (hereinafter referred to as speedometer). It is mainly used to test the accuracy of automobile speedometer. Model SD-3/10A/13A and B speedometer are suitable for all types of cars with axle loads not more than 3 000, 10 000 and 13 000㎏.
KNOW MORE
Let s talk! We’ll provide the perfect solution for you！
The products provided by Henan Wanguo Technology Co., Ltd. are all developed and produced in accordance with relevant national standards, with strict control and quality inspection. Unqualified products will never leave the factory.
Long Ding Chuangfu Center, High-tech Zone, Zhengzhou City, Henan Province
