The automobile flat-panel testing platform is suitable for testing vehicles with the maximum dynamic weight of a single axle not exceeding 10000kg. On the flat-panel simulating the actual flat road, the automobile runs at a certain speed, implements braking, and dynamically measures the braking force, axle load
The automobile flat-panel testing platform is suitable for testing vehicles with the maximum dynamic weight of a single axle not exceeding 10000kg. On the flat-panel simulating the actual flat road, the automobile runs at a certain speed, implements braking, and dynamically measures the braking force, axle load, suspension and other testing items at one time. The test items are as follows: the dynamic and static single wheel weight and the maximum braking force of the total axle load of the automobile; the braking force of each wheel ④ braking force process curve ⑤ braking force sum, braking force process difference ⑤ vehicle deceleration, test speed ⑤ suspension efficiency and suspension vibration curve.
Research and development basis
1,GB/T28529－2012
Flat Brake Test Bench
2,JJG1020-2007
Verification Regulation of Flat Brake Test Bench
Technical characteristics
The brake platform meets the national standard GB 21861-2014 "Items and Methods of Motor Vehicle Safety Technical Inspection".
Adopt integral design, which can be installed quickly.
The platform body adopts square steel tube, which has stable structure and high strength.
The brake plate adopts special sand-sticking technology, which is wear-resistant, long in service life and high in braking test ability, and can truly simulate the braking situation of the road surface.
The control acquisition system is integrated and embedded, with reasonable structure, efficient and convenient installation and maintenance.
Adopt high-precision sensor, with good repeatability, accuracy and reliability.
With standard communication interface, it is convenient for equipment networking.
technical parameter
| model | 3t |
| Allowable axle load mass(kg) | 3000 |
| Wheel weight test range(kg) | ≥3000 |
| Test range of wheel braking force(DAN | ≥1350 |
| Resolution: wheel weight (kg) | 1 |
| Resolution: braking force (DAN) | 1 |
| Indication error: wheel weight | ±2 |
| Indication error: braking force | ±2 |
| Sand adhesion coefficient | ≥0.75 |
| Combination form of sand-adhering plates (four plates) | Two pieces and four boards |
| Single small board size (LxW)mm | 2000*940 |
| Size of single bonded sand board (LxW)mm | 2000*910 |
| Effective test size of single table, mm | 2000*910 |
| Measurable wheelbase range (m) | 0.85~4 |
| Test speed (km) | 5~10 |
| structural style | Frame welding |
| Power Supply | AC220V ±10%，50±1Hz |
Leave your contact information, and our engineers will help you find the solution you are looking for.
ZD-3BW/10BW, ZD-10DW/13DW, ZD-18BW, ZD-18DW series automobile loading and braking test stands are mainly used for testing automobile braking performance under rated load quality, and can detect the braking force sum and braking force difference (maximum process difference) of each axle of the automobile;
KNOW MORE
Drum-type automobile speedometer inspection platform (hereinafter referred to as speedometer). It is mainly used to test the accuracy of automobile speedometer. Model SD-3/10A/13A and B speedometer are suitable for all types of cars with axle loads not more than 3 000, 10 000 and 13 000㎏.
KNOW MORE
Motorcycle safety performance testing equipment is used to test motorcycle wheel (axle) weight, speedometer accuracy, braking performance and wheel deflection. Friction inspection equipment is suitable for two-wheeled, three-wheeled and three-wheeled motorcycles that meet the following table.
KNOW MORE
Handheld terminal installed with relevant mobile application software, which is specially used for motor vehicle inspection or motor vehicle safety technical inspection.
KNOW MORE
Product introductionWGDP-10/13/15 automobile suspension steering system clearance tester (hereinafter referred to as product) is used to check the clearance between automobile suspension system and steering system matching parts. This product is suitable
KNOW MORE
Functional useThrough the intelligent measuring device, the three-dimensional image of the vehicle profile and the comprehensive monitoring data of length, width, height, container rail height, wheelbase and pin wheelbase are obtained. For the semi-trailer type, the tractor and the trailer can pass through the system together, and the relevant information of the tractor and the trailer can be measured
KNOW MORE
Product introductionThe automobile suspension device inspection table (hereinafter referred to as the suspension table) can carry out the following tests on automobile suspension devices with axle weight less than 3 t:
KNOW MORE
Automobile 4-in-1 testing equipment is specially designed to meet the requirements of automobile 4S stations, maintenance service centers, small automobile testing stations, bus passenger stations, teaching and scientific research units, etc. It occupies less land, has high testing accuracy and simple operation, and is widely used in automobile repair shops, 4S shops, etc.
KNOW MORE
Automobile three-in-one testing equipment is specially designed to meet the requirements of automobile safety performance index testing in automobile 4S stations, maintenance service centers, small automobile testing stations, bus passenger stations, teaching and scientific research units, etc. It occupies less land, has high testing accuracy and simple operation, and is widely used in automobile repair shops and 4S shops.
KNOW MORE
Product introductionThis wheel gravimeter is used to measure the wheel mass, axle load mass and vehicle mass. Can be used independently, and can also be used for on-line use of automobile detection lines. LZ-3B/10B/13B wheel weight tester is suitable for two-axle vehicles with wheel weights
KNOW MORE
This test bench is mainly used to dynamically measure the front wheel side slip of an automobile and judge whether it is abnormal. WGCH-3F/10F/13F/13FS is suitable for all types of automobiles with axle load mass not more than 3000/10000/10000/13000/13000kg.
KNOW MORE
The automobile flat-panel testing platform is suitable for testing vehicles with the maximum dynamic weight of a single axle not exceeding 10000kg. On the flat-panel simulating the actual flat road, the automobile runs at a certain speed, implements braking, and dynamically measures the braking force, axle load
KNOW MORE ZD-3BW/10BW, ZD-10DW/13DW, ZD-18BW, ZD-18DW series automobile loading and braking test stands are mainly used for testing automobile braking performance under rated load quality, and can detect the braking force sum and braking force difference (maximum process difference) of each axle of the automobile;
KNOW MORE
Drum-type automobile speedometer inspection platform (hereinafter referred to as speedometer). It is mainly used to test the accuracy of automobile speedometer. Model SD-3/10A/13A and B speedometer are suitable for all types of cars with axle loads not more than 3 000, 10 000 and 13 000㎏.
KNOW MORE
ZD-3BW/10BW, ZD-10DW/13DW, ZD-18BW, ZD-18DW series automobile loading and braking test stands are mainly used for testing automobile braking performance under rated load quality, and can detect the braking force sum and braking force difference (maximum process difference) of each axle of the automobile;
KNOW MORE Drum-type automobile speedometer inspection platform (hereinafter referred to as speedometer). It is mainly used to test the accuracy of automobile speedometer. Model SD-3/10A/13A and B speedometer are suitable for all types of cars with axle loads not more than 3 000, 10 000 and 13 000㎏.
KNOW MORE Motorcycle safety performance testing equipment is used to test motorcycle wheel (axle) weight, speedometer accuracy, braking performance and wheel deflection. Friction inspection equipment is suitable for two-wheeled, three-wheeled and three-wheeled motorcycles that meet the following table.
KNOW MORE Handheld terminal installed with relevant mobile application software, which is specially used for motor vehicle inspection or motor vehicle safety technical inspection.
KNOW MORE Let s talk! We’ll provide the perfect solution for you！
The products provided by Henan Wanguo Technology Co., Ltd. are all developed and produced in accordance with relevant national standards, with strict control and quality inspection. Unqualified products will never leave the factory.
Long Ding Chuangfu Center, High-tech Zone, Zhengzhou City, Henan Province
